Station keeping of high power communication satellites

Station keeping of high power communication satellite

Provisional specification for satellite time in a geomagnetic environment

Satellites in geosynchronous orbit were experiencing operational anomalies. These anomalies are believed to be due to the environment charging the spacecraft surfaces to a point where discharges occur. In designing future satellites for long term operation at geosynchronous altitude, it is important that designers have a specification that will give the total time per year, the particle flux density and particle energies that their satellites can be expected to encounter in these substorm environmental conditions. The limited data currently available on the environmental conditions are used to generate the provisional specification given in this report

Very high voltage latching relay

Relay consists of high voltage reed switch actuated by rotating permanent magnet mounted on stepper motor shaft, with actuation assembly isolated from high voltage circuit. Unit can be modified for use as double pole or double pole double throw latching relay and can be used in either air or vacuum

Process for preparing liquid metal electrical contact device

The parts of an electrical contact device are treated by sputter etching to remove the parent metal oxide. Prior to exposure of the electrodes to any oxygen, a sacrificial metal is sputter deposited on the parts. Preferably this sacrificial metal is one that oxidizes slowly and is readily dissolved by the liquid metal. The sacrificial metal may then be removed from unwanted areas. The remainder of the ring and the probe to be wet by the liquid metal are submerged in the liquid metal or the liquid metal is flushed over these areas, preferably while they are being slightly abraded, unitl all the sacrificial material on these portions is wet by the liquid metal. In doing so the liquid metal dissolves the sacrificial metal and permanently wets the parent metal. Preferred materials used in the process and for the electrodes of electrical contact devices are high purity (99.0%) nickel or AISI type 304 stainless steel for the electrical contact devices, gallium as the liquid metal, and gold as the sacrificial material

A study of the intensity of the self-broadened fundamental band of hydrogen chloride

Intensity study of self-broadened fundamental band of hydrogen chlorid

Titanium honeycomb structure

A brazed titanium honeycomb sandwich system for supersonic transport wing cover panels provides the most efficient structure spanwise, chordwise, and loadwise. Flutter testing shows that high wing stiffness is most efficient in a sandwich structure. This structure also provides good thermal insulation if liquid fuel is carried in direct contact with the wing structure in integral fuel tanks

Liquid Level Sensor for High Temperature Molten Salt in Confined Container

Electrical resistance measurements on different rod materials in liquid solutions, molten salts, or molten lead are considered to design a liquid level sensor in a sealed containers when the temperature of the fluid is very high (~1000ºC) and conventional measurements are not possible due to properties of the fluid or condition of the container. An analytical solution to the problem is adopted to reduce the cost of the sensor and overcome the difficulties of calibration of sensors at high temperature for prediction of the level of liquid. An electrical circuit model is suggested for analytical solution to compute the resistivity versus height of the electrode rod submerged in the liquid in a narrow container. Good prediction of circuit model for experimental results is verified by comparison of analytical results of different combination of liquid solutions and rods’ material with experimental graphs

Provisional specification for satellite time in a geomagnetic substorm environment

Satellites in geosynchronous orbit have been experiencing operational anomalies. These anomalies are believed to be due to the environment charging the spacecraft surfaces to a point where discharges occur. In designing future satellites for long term operation at geosynchronous altitude, it is important that designers have a specification that will give the total time per year, the particle flux density, and particle energies that their satellites can be expected to encounter in these substorm environmental conditions. The limited data currently available on the environmental conditions was used to generate the provisional specification given

Low cost tracking Navaids error model verification

Features and characteristics of the tracking navaids (Microwave Scanning Beam Landing System, Radar Altimeter, Tacan, rendezvous radar and one way Doppler extracter) were investigated. From the investigation, a set of specifications were developed for building equipment to verify the error model of the tracking navaids. Breadboard verification equipment (BVE) was built for the Microwave Scanning Beam Landing System and the radar altimeter. The breadboard verification equipment generates signals to the tracking navaids which simulate the space shuttles trajectory in the terminal area. The BVE simulates sources of navaids error by generating pseudorandom perturbations on the navaids signals. Differences between the trajectory value and the navaid derived values are taped and form the basis for the navaids error model